Cornelius Keg / Demijohn Brush

$17.50 -- Extra large brush for cleaning out those kegs and demijohns. Rugged brush that is 36" long and has 6" diameter bristles. (corne keg not included)

Purchase Cornelius Keg / Demijohn Brush

SKU: F23

Other products in the category Beer Brewing / Beer Kegs & Kegging:

5 Gallon Cornelius Keg (used, Ball Lock ) -- Used 5 gallon soda kegs. Each keg has been pressure tested to ensure a good seal. O-rings that are currently installed are not new, so a new o-ring kit is included. Measures approx 26" high (with the in and out fittings connected), and 8.5" in diameter

O-Ring Set for Cornelius Kegs -- All the o-rings for your keg. Large ring for the lid, two for the poppets, 2 for dip tubes.

Co2 Regulator With Turn Valve -- New QUALITY regulator. Two gages--one for bottle pressure, one for line pressure. Comes with internal check valve. The best pressure regulator out there for kegging systems.

High Pressure Gage 0-2000 psi -- Replacement gage, shows CO2 bottle pressure. Available in both right and left hand thread. Please determine which you need prior to ordering. Measures from 0-2000 psi, with a red "Order Gas" zone, below 500 psi.

Low (Line) Pressure Gage, 0-30 psi -- Replacement gage for the gas line (low pressure) side of regulator. Right hand thread only, 0-30 psi. Dial face is 2" in diameter.

Mini Co2 Regulator - Ball Lock -- The mini-reg features total portability with all the features of a full size regulator.

New 5 Lb. Aluminum Co2 Tank -- A NEW, lightweight aluminum CO2 tank.

Stainless Steel 0.5 Micron Carbonation Stone -- Carbonates your kegged beer in minutes. By connecting this stone to a 1/4" hose and your CO2 "in" line, the bubbles come up thru your beer as a super-fine mist, and easily go into solution. Active part of the stone is about 1 inch long.

CO2 Tank Gasket - Set of 2 Gaskets -- Set of 2. This is the hard plastic gasket that goes between your CO2 tank and your regulator.

Quick Disconnect-Ball In Fitting -- Gas in fitting for ball lock corney kegs. Barbed end.

Quick Disconnect Fitting- In W/Ftgs -- Gas-in fitting for ball lock cornelius kegs. This one has a threaded connection for easy change.

Quick Disconnect-Ball Out Fitting -- Beer out fitting for ball lock cornelius kegs.

Quick Disconnect Ball/Out W/Ftgs -- Beer out fitting for ball-lock style kegs. Allows easy interchange of fittings.

Pin Lock Fitting-Beer Out (3-Pin) -- For "Coke" style cornelius kegs. The beer-out fitting has 3 pins on the connector.

Pin Lock Gas In Fitting (2 Pin) -- For "Coke" style cornelius kegs. The gas-in fitting has 2 pins.

Quick Disconnect Pin/Beer Out W/Ftgs -- For "Coke" style cornelius kegs.

Quick Disconnect PinLock Gas-In W/Ftgs -- For "Coke" style cornelius kegs.

Plastic Tapper Spigot -- The fun end of the setup. Also called a cobrahead or picnic faucet. Hand-held plastic faucet for dispensing beer, soda pop etc.

1/4" Id Gas Line (Thick Wall) - Per Foot" -- Recommended for all gas (CO2) lines. Thick wall for secure, easy clamping.

3/16" Beer Line, Thick Wall Per Foot" -- Recommended, even tho it's a tight fit, to provide some restriction on your beer line. This allows you to use a higher keg pressure and keeps your beer carbonated. Thick wall tubing for secure, easy clamping.

Cornelius Kegging System Setup & Maintenance - Leaflet -- The name says it all. Details of kegging for the home brewer. By Homebrew Heaven. 6 pgs.

Beer Line Cleaning Kit - Complete! -- Nothing ruins a fine beer like a dirty or contaminated beer line or faucet. This kit includes Foxx Superflush Cleaner, Pump, Bottle, Beer Faucet Brush and Faucet Wrench

Chrome Gage Protector (Gage Cage) -- Bolts on to your Regulator and protects your gages from bumps. Will save you $$$ in broken gages. Worth having if you take your kegging system out for parties.

Double Draft Beer Tower -- Complete with all parts and ready to install •Includes faucets •Includes 5ft - 3/16" tubing with tailpieces, hex nuts and washers •Styrofoam insulated stainless steel barrel (not pvc like others) to prevent sweating. Brass Finish (extra) is shown.

Single Draft Tower -- Same as above, but with one spigot. Finish is chrome. (not pvc tubing!)

3-Way Gas Manifold W/Shutoffs -- All-metal manifold with 3 controls

BeerGun Stainless Bottle Filler -- One-handed intuitive operation. Everything that touches the beer is stainless steel. Low foaming. The BeerGunTM comes with everything pictured here - a 10ft length of 3/16" ID hose and a brush for cleaning the inside of the tubes.

Optional Accessory Kit for BeerGun -- This optional accessory kit provides everything you need to get your BeerGun up and running! Click on product name for more information

Thru Wall Shank W/ Chrome Faucet -- Spiff up your refrigerator with a tap on the outside. Add MORE taps! Build your own kegerator or jockey box.

1/4" Barbed Tailpiece -- tailpiece for the end of your faucet shank or sankey tap

3/16" Barbed Tailpiece -- tailpiece for the end of your faucet shank or sankey tap

Beer Faucet Wrench -- Used for tightening/loosening beer taps

Beer Washer -- Beer washer for those sankey taps and faucet shanks

Carbonator -- Used to carbonate your plastic 2 Liter Soda-Pop bottles using a CO2 bottle and ball-lock fitting. This may be done overnight. Lower temperatures, higher pressures, and more agitation will increase the carbonation level.

Counterpressure Bottle Filler W/Quick Valves -- Used to bottle beer from kegs. Purges the bottle with CO2 prior to filling.

Drip Tray - Stainless Steel -- Brushed stainless steel tray, back and grating. 1/2" copper drain tube. Measures 4" deep, 6" wide with two drilled holes for easy installation onto your 'fridge, kegerator, wall...you name it.

Hex Nut -- This nut connects to the end of our faucet shank and also is connected to the ends of a sankey tap

In-Line Check Valve (Gas) -- Used to prevent backflow into regulator/beer lines

Keg Faucet Tap (Handi-Tap) -- A handy little item. Directly connects a spigot to your corney keg. For a completely portable kegging system, consider getting a Keg Charger!

Keg Lube (Petro-Gel) For Keg O-Rings -- Apply a thin film to o-rings to prevent leaks and make removal of keg fittings easy. Food grade grease.

Modular 2 Way Gas Distribution Manifold -- Allows you to add more kegs to your system, and still control gas flow.

Plastic "T" Fitting For Gas or Beer Line -- Used to split a gas or beer line for multiple kegs.

Pony Pump For Sanke Keg -- Handy tap for picnics (and KEGGERS!). Don't forget to invite Ralph, the webmaster of Homebrew Heaven. He likes beer, too! Just pump in some air, and out comes fun...

Sanke Beer Tap (Coupler) for 15.5 Gal Kegs -- For 15.5 Gal Sanke style kegs. Requires CO2 bottle, regulator, beer line, gas line and tap.

Sanke Keg Picnic Tap (Airpump) -- Great for parties. Fits 15.5 gallon Sankey type fitting.

Stainless Steel "Cross" Fitting For Gas Line -- Used to split the gas line for running multiple kegs.

Stainless Steel "T" Fitting For Gas or Beer Line -- Used to split a gas or beer line for multiple kegs.

Stainless Steel Hose Clamps -- Used to connect Cornelius fittings to gas and beer lines.

Swivel Nut Assy. -- To connect some types of Regulators to Gas Line or to connect to the C92C and C92D Corne Keg fittings. One of these is included with the C91 Regulator.